Mazak CNC 屏幕操作警报错误代码

MAZATROL MATRIX等Mazak CNC屏幕操作错误列表

对于其他 Mazak 警报列表，请访问以下页面。

• Mazak 系统/驱动器错误（编号 1 – 编号 99，编号 1000 – 编号 1099）
• Mazak CNC 机器控制错误（No. 100 – No. 199，No. 1100 – No. 1199）
• Mazak PLC机器控制错误（No. 200 – No. 399, No. 1200 – No. 1399）
• Mazak CNC 屏幕操作错误（No. 400 – No. 499，No. 1400 – No. 1499）
• Mazak I/O 错误（编号 500 – 编号 599，编号 1500 – 编号 1599）
• Mazak MAZATROL 程序错误（No. 600 – No. 699，No. 1600 – No. 1699）
• Mazak MAZATROL 程序错误（No. 700 – No. 799，No. 1700 – No. 1799）
• 马扎克 EIA/ISO 程序错误（编号 800 – 编号 899，编号 1800 – 编号 1899）
• 马扎克 EIA/ISO 程序错误（编号 900 – 编号 999，编号 1900 – 编号 1999）
• Mazak 干扰错误（编号 2100 – 编号 2199）

CNC 屏幕操作错误

400

——
原因
——
动作
——

401 非法格式

原因
输入数据的格式不可用。
示例：负数据已输入到拒绝负数据输入的项目。
操作
按数据取消键，然后输入正确的数据。

402 非法数字输入

原因
1.指定了显示禁止程序的工作号。
2．输入的数值超出允许范围。
操作
1.禁止显示的程序不能进行相关操作（程序管理功能）。
2．按清除键，然后输入正确的数据。

403 程序太大

原因
已超过每个程序 2000 行的限制。
操作
重新创建程序，使其包含 2000 行或更少。

404 内存容量超出

原因
1.加工程序数据存储容量已满，无法再创建加工程序。
2．由于已经存储了 100 组此类数据，因此不再可能额外准备过程控制数据。
3.由于已经存储了 4000 组此类数据，因此不再可能额外准备程序布局数据。
操作
通过从内存中删除不需要的加工程序或将加工程序保存到外部存储器来腾出可用的存储区，然后创建新的加工程序。

405 程序号未找到

原因
试图选择一个其工作编号尚未注册的程序。
操作
选择一个已经注册了工号的程序。

406 内存保护

原因
1.对禁止编辑的程序进行了禁止操作（编辑、擦除、工号重编、名称录入）。
2．操作面板上的PROGRAM LOCK/ENABLE开关设置到LOCK位置。
3．试图在刀具数据显示上执行“刀具名称命令”操作，同时刀具保持在主轴中。
操作
1.禁止编辑的节目不能进行相关操作（节目管理功能）。
2．将 PROGRAM LOCK/ENABLE 开关设置到 ENABLE 位置。
3.将刀具从主轴上取下，再进行一次操作。

407 未找到指定数据

原因
指定的数字或字符串在程序中不存在。
处理
指定一个存在的数字或字符串。

408 程序错误

原因
加工程序数据存储区的内存内容已被破坏。
处理
删除对应的程序。

409 非法插入

原因
无法插入程序数据。
操作
不可在公共单元前插入数据。

410 非法删除

原因
无法删除程序。
– 在编辑 MAZATROL 程序期间试图删除公共单元。
措施
不可删除公共单元。
– 将光标移动到数据所在位置后编辑程序。

411 程序编辑期间断电

原因

程序编辑过程中可能因断电导致部分程序损坏。
操作
检查相应程序是否有错误数据，如有错误则更正程序数据。

412 超出子程序嵌套

原因
子程序嵌套重复次数超过九次。
处理
修改程序，使子程序嵌套的总重复次数为9次或以下。

413 最大。超出注册程序数量

原因
程序注册已超过其可用的最大值（标准：256 个程序）。
操作
通过删除不需要的程序或将它们移动到备份区或将不需要的程序保存在外部存储单元中然后删除它们来减少注册程序的总数。

414 自动计算不可能

原因
无法自动计算圆周速度和进给速度。
注意：在加工
导航-预测显示中选择[导航]菜单功能时显示的子错误代码如下所示.
–1：MAZATROL程序文件打开错误
–2：MAZATROL程序文件读取错误
–3：刀具材料不匹配错误（获取刀具材料编号时）
–4：表面速度自动设置错误
–5：工件材料上限值基本系数相关的文件打开错误
–6：工件材料不匹配错误
–7 ：与表面速度数据表相关的文件打开错误
–8：工具材料不匹配错误
2：导航文件丢失
措施
检查并修正程序的刀具顺序数据或加工单元。

415 MIS-SET G代码

原因
指定了不在规格范围内的G代码。
行动
检查并修改程序中的G代码地址。

416 自动处理不可能

原因

加工单元数据错误，无法自动开发刀具。
处理
检查修正加工单元数据。

417 禁止编辑

原因
试图修改禁止编辑的程序。
操作
取消禁止编辑参数设置后才能修改数据。

418 EIA/ISO 转换

原因
在EIA/ISO 转换过程中，试图对转换源程序执行擦除、工作编号更改或编辑。或者已尝试选择刀具路径检查显示。
操作
在EIA/ISO转换过程中，不能进行转换源程序的擦除、工件编号更改或编辑。
不能选择刀具路径检查显示。

419 自动点击过程不可能

原因
1.攻丝装置数据中的丝锥公称直径不正确，导致无法自动设置螺距或其他数据。
2．尽管管道分接头自动设置（D95 位 0 =1）引用了文本文件，但由于自动设置文本文件（Pipescdt.txt）不正确或不包含数据，因此无法执行自动设置功能。
动作
1.检查并修正程序的攻牙单元数据和攻牙顺序数据。
2．检查并更正自动设置文本文件（Pipescdt.txt）。

420 相同的数据存在

原因
试图输入与已经注册的数据相同的数据。
1。 TOOL LAYOUT显示中的刀库编号。
2．加工程序号（已更改）
3．加工优先序号
动作
检查并更正数据设置。

421 数据未找到

原因
试图指定不存在的数据。
操作
检查指定数据是否存在。

422 内存保护（I/O 忙）

原因
在I/O操作中试图编辑或输入加工程序、刀具数据等。
处理
等待I/O操作完成，再从头重复编辑或输入操作。

423 超过最大工具数

原因
刀具排版时，指定程序中使用的刀具数量已超过最大可用数量。
操作
检查并修正相应的加工程序，不超过最大可用刀具数。

424 所有口袋号码未分配

原因
无法完成刀具布局操作，因为刀库编号尚未分配给所有需要的刀具。
操作
分配刀套号，完成排刀操作。

425 数据丢失

原因
由于缺少数据，无法处理。
1。未在DATA I/O 显示上指定任何数据（例如工作编号等）就试图保存或加载。
2.需要输入重新启动操作的数据。
操作
正确输入数据。

426 程序数据丢失

原因

由于加工单元数据部分缺失，无法自动生成刀具序列数据。
操作
用数据填充所有加工单元数据项。

427 内存保护（自动模式）

原因
试图在自动操作模式下输入不允许的数据。
措施
将模式切换到手动操作模式，然后输入数据。

428 内存保护（自动操作）

原因
试图在自动操作期间在显示器（例如工具数据显示器）上输入不允许的数据。
措施
只有在将NC单元置于其复位状态或将当前模式切换到另一种模式后才能输入允许的数据。

429 无法执行测量

原因
不满足以下条件：
坐标测量
1．不得进行自动操作。
2。主轴上必须装有刀具。
3．主轴上所装刀具的刀具数据必须已经输入。
刀具长度测量
1．不得进行自动操作。
操作
设置指定条件，然后进行测量。

430 非法工具指定

原因
在创建加工程序期间，已尝试在刀具序列中输入对特定程序单元不可用的刀具名称。
操作
指定正确的刀具名称。

431 非法托盘号

原因
指定了一个不存在的托盘编号。
行动
Designate a correct pallet number.

432 ILLEGAL TOOL No.

Cause
A nonexistent tool number has been designated.
Action
Designate a correct tool number.

433 SAME PROGRAM EXISTS

Cause
The number of the machining program that has been designated for program reading from an external unit already exists within the NC memory.
Action
Check the number of the machining program.

434 NO ASSIGNED TOOL IN TOOL FILE

Cause
The milling tools (face-mills, end-mills, chamfering cutters, and ball end-mills) that have been designated on the machining program include a one(s) that is not yet registered in the TOOL FILE display.
Action
Register the corresponding tools in the TOOL FILE display.

435 PROGRAM CHECK NOT ALLOWED

Cause
An attempt has been made to restart on the TOOL PATH display during checking of the tool path.
Action
Interrupt the tool path checking operation before restarting.

436 UNREGISTERED TNo.

Cause
An unmeasurable tool number has been designated in the automatic tool-length (diameter) measurement mode.
Action
Designate a measurable tool number.

437 NO NOM-φ DATA IN PROGRAM

Cause
It has been found during tool layout that there is a tool without a nominal diameter in the designated program.
Action
Check if nominal diameters have been assigned to all tools registered in the designated program.

438 END UNIT NOT FOUND

Cause
The end unit is not included in the machining program.
Action
Create the end unit at the end of the program.

439 MAZATROL PROGRAM DESIGNATED

Cause
A MAZATROL program has been designated for copying purposes during EIA/ISO program editing.
Action
No MAZATROL programs can be designated for copying purposes during EIA/ISO program editing.

440 EIA/ISO PROGRAM DESIGNATED

Cause
1. The machining program that has been designated on the TOOL LAYOUT, PROCESS CONTROL or SET UP RECORD display is an EIA/ISO program.
2. An EIA/ISO program has been designated for copying purposes during MAZATROL program editing.
3. An EIA/ISO program has been designated as the source program of EIA/ISO conversion.
4. An EIA/ISO program has been designated when writing coordinate values on the MEASURE display.
Action
No EIA/ISO programs can be designated for operation on the TOOL LAYOUT, PROCESS CONTROL, SET UP RECORD or MEASURE display or during EIA/ISO conversion or MAZATROL program editing.

441 UNREGISTERED HEAD DATA

Cause
The head number that has been designated during MDI-MMS setting does not exist in the head data.
Action
Review the designated head number.

442 DATA RENEWAL NOT ALLOWED

Cause
No updates can be made to the machining program.
Action
This message may also be displayed when the NC unit is busy processing data. Press the clear key and then carry out the operation once again.

443 HELP IS NOT AVAILABLE

Cause
No help display is prepared for the line on which the cursor is placed.
Action
Refer to the Programming Manual (MAZATROL).

444 EDITING PROHIBITED AREA

Cause
During automatic operation based on the EIA MONITOR display, an attempt has been made to move the cursor to the program section whose editing was prohibited.
Action
The cursor cannot be moved to the area where editing is prohibited.

445 ILLEGAL UNIT

Cause
An attempt has been made to set tool layout data in a MAZATROL program containing an illegal unit(s).
Action
Review the program.

446 RESTART TIMES EXCEEDED

Cause
The block to be searched for at the time of restart of the EIA/ISO program does exist, but the designated number of times of reappearance of the block is too large.
Action
Check the number of times of reappearance of the block.

447 PROGRAM ERROR

Cause
A program error(s) has occurred during EIA/ISO restart search.
Action
The program being searched for includes an error(s). Perform a tool-path check upon the program contents.

448 RESTART SEARCH UNFINISHED

Cause
EIA/ISO restart searching has not been executed.
Action
Designate the restart position and press the [EIA/ISO SEARCH] button to search the intended restart position.

449 RESTART SEARCH FINISHED

Cause
An attempt has been made to carry out another search operation when EIA/ISO restart searching had already been finished.
Action
Press the reset key and then carry out the restart operation once again.

450 TOUCH SENSOR NOT IN SPINDLE

Cause
The spindle did not have a mounted touch sensor when an attempt was made to set MAZATROL coordinate measurement data on the PROGRAM (MAZATROL) display.
Action
Mount a touch sensor in the spindle before setting the data.

451 SAME MATERIAL ENTERED

Cause
The materials name that has been designated on the CUTTING CONDITION – W.-MAT/T.-MAT. display already exists.
Action
Designate a new materials name.

452 NO SHAPE DATA IN UNIT

Cause
No shape data exists in the program unit that has been designated in an attempt to make a copy of shape data.
Action
Check the contents of the program unit for which shape copying is to be made.

453 NO SHAPE DATA TO COPY IN UNIT

Cause
An attempt has been made to copy shape data whose type is not available for the particular program unit.
Action
It is not possible to copy shape data of the pallet-changing unit, index unit, or other units that do not have a shape sequence.

454 CURSOR POSITION INCORRECT

Cause
Processing not permissible for the current cursor position has been attempted.
Example 1:An attempt has been made to carry out a shape copying operation with the cursor on the tool sequence line.
Example 2:The SHAPE CHECK display has been selected on a shape sequence line not actually executed during automatic operation.
Action
Example 1:No shape data can be copied on the tool sequence line.
Example 2:Review the program.

455 SAME PROGRAM No. DESIGNATED

Cause
The machining program currently being edited has been appointed for the particular program copying operation.
Action
Copying within the same program is not possible. Check the designated program number.

456 NO TOOL IN SPINDLE

Cause
The spindle does not currently have a tool mounted on it.
Action
After mounting a tool on the spindle, carry out the particular operation once again.

457 DATA ADDRESS NOT FOUND

Cause
During creation of manual program mode unit, data setting has been attempted without addressing.
Action
During creation of the manual program mode unit, designate an address before setting data.

458 INTERFERING TOOL REGISTERED

Cause
An attempt has been made to register a tool most likely to interfere with an adjacent pocket.
Example 1:An attempt has been made to register tool data or tool change data on the TOOL DATA display.
Example 2:An attempt has been made to set such a tool on the TOOL LAYOUT display that is likely to interfere with an adjacent pocket.
Action
Select a pocket that does not cause interference with an adjacent one.

459 DISPLAY PROTECT

Cause
An attempt has been made to display a program whose display is prohibited.
Action
Display the program only after canceling the parameter setting of prohibition of display.

460 PRINTER IN OPERATION

Cause
An attempt was made on the TRACE display to perform display scaling change, material shape and tool path drawing while the hard copy is being made.
Action
After finishing the hard copy, carry out the operations.

461 PRIORITY No. OVERLAP

Cause
The same priority number is assigned to different tools.
Action
Within one process, the same priority number must not be assigned to different tools.
Change the priority number.

462 ILLEGAL PRIORITY NUMBER

Cause
The priority numbering order within a unit is not correct.
Action
The machining order within one unit has been reversed by the incorrect priority numbering.
Change the priority numbers.

463 PRIORITY No. OVERFLOW

Cause
A priority number exceeding 99 has occurred because an attempt has been made to move a priority number(s) on the PROGRAM LAYOUT display.
Action
Set priority numbers in the correct order, and then move the desired priority number(s).

464 ILLEGAL ADDRESS INPUT

Cause
An address not covered by the specifications has been designated during input of subprogram unit addresses on the PROGRAM (MAZATROL) display.
Action
Check and correct the address.
Check the specifications.

465 EIA SHAPE DATA NOT FOUND

Cause
Although an attempt has been made to draw a workpiece shape using the selected EIA/ISO program, shape data is not present in that program.
Action
Review the program.
If the program is that which has been obtained by EIA/ISO conversion output, change the setting of the bit 0 of parameter F89 to 1 and then carry out the converting operation once again.

466 INCORRECT EIA SHAPE DATA

Cause
Although an attempt has been made to draw a workpiece shape using the selected EIA/ISO program, the corresponding shape data is not correct.
Action
Review the program.

467 MEMORY PROTECT (SAMPLING)

Cause
An attempt was made during load sampling to change the axis to be monitored or the sampling time.
Action
Perform the required change after the current sampling.

468 MAINTENANCE CHECK WARNING

Cause
The target time of the items which had been set on the MAINTENANCE CHECK display has been exceeded.
Action
Carry out periodic checks, and then after completion of the checks, reset the current time of the check items of the MAINTENANCE CHECK display to zero (0).

469 TPC DATA EDIT IMPOSSIBLE

Cause
The TPC data setting is not possible for the designated unit.
Action
Check the program.

470 ILLEGAL TPC DATA

Cause
The TPC data for the unit is not correct.
After setting the TPC data, the unit machining mode has been changed.
Action
Delete the TPC data and set correct TPC data once again whenever required.

471 TPC DATA NOT FOUND

Cause
While the cursor was on a line of unit not containing TPC data on the display, the [TPC] menu key was pressed during the program list mode.
Action
Press the [TPC] menu key after shifting to the programming mode.

472 CALCULATION ERROR

Cause
1. The calculation expressions displayed in the desk calculator window includes expressions that result in a calculation failure.
2. Calculating tool lengths A and B has been attempted in spite of tool nose position storage not being completed.
Action
1. Review the calculation expressions, and correct nonexecutable sections, such as those which may include division by 0 or result in a negative number in SQRT.
2. Store the position of the tool nose.

473 FINAL POINT DATA NOT FOUND

Cause
Although the end-point data of the preceding line was not yet set in the BAR or CPY unit, the [NEXT] menu key was pressed.
Action
Press the [NEXT] menu key after setting the end-point data of the preceding line.

474 NO PROGRAM DISPLAY (TAPE MODE)

Cause
1. During tape operation mode, an attempt has been made to select the EIA MONITOR display.
2. An attempt has been made to change the operation mode to tape operation mode when the EIA MONITOR display is selected.
Action
1. During tape operation mode, programs cannot be displayed on the EIA MONITOR display.
2. Select a display other than the EIA MONITOR display before changing the operation mode to tape operation mode.

475 NO EIA/ISO OPTION

Cause
An attempt has been made to use an EIA/ISO-option related function in spite of the absence of an EIA/ISO option.
Action
An EIA/ISO-option related function cannot be used since the system has no EIA/ISO option.

476 NO OPTION

Cause
An attempt has been made to use an optional function in spite of the absence of that option.
Action
This function cannot be used since the system does not have the option for the function.

478 MEMORY PROTECT (MEASURING)

Cause
An attempt has been made to copy the coordinates data in WRITE DATA column of the MEASURE display into the designated position, while measurement using the MEASURE display is in progress.
Action
Copy the coordinates data only after the measurement has been completed.

480 CARD NOT READY

Cause
Executing the memory card I/O function in DATA I/O display mode has been attempted when a memory card was not set.
Action
Set a memory card before using the memory card I/O function.
If a memory card has been set, confirm the insertion direction of the memory card and set it again. If the alarm recurs even so, the memory card is likely to be damaged; replace the memory card and re-execute the I/O function.

481 DIRECTORY NOT FOUND

Cause
Input/output operations on a directory not present in the memory card have been attempted during memory card I/O in DATA I/O display mode.
Action
Check whether the specified directory is present.

483 SOLID DESCRIP. IMPOSSIBLE UNIT

Cause
Checking the program including the units or conditions (such as the case that angle B is set in the index unit of the initialpoint scheme) that do not allow graphics to be drawn in SOLID mode has been attempted in the SOLID mode of the TOOL PATH CHECK display.
Action
Before checking the tool path, cancel the SOLID mode or delete the unit that cannot be drawn in the SOLID mode.

484 INCORRECT SPINDLE TOOL

Cause
The [LENG-OFS TEACH] menu key has been pressed in spite of the fact that a tool not having its “Length Offset Data” item displayed in TOOL DATA display mode (for example, a turning tool) was mounted in the spindle.
Action
Check the tool mounted in the spindle.

485 INCORRECT HEAD INDEX

Cause
Executing the tool nose position storage function (TEACH) has been attempted when the head index angle displayed in TOOL DATA display mode was neither 0 degrees, 90 degrees, nor 180 degrees.
Action
Execute the tool nose position storage function (TEACH) when the head index angle is either 0 degrees, 90 degrees, or 180 degrees.

486 ILLEGAL JAW DATA

Cause
The use of the jaw shape that has been specified for the program results in interference between adjacent jaws as a result of the SOLID mode PATH CHECK.
Action
Review the jaw data or the workpiece-gripping diameter value.

487 LONG BORING BAR ADAPTER EXISTS

Cause
Assigning a tool other than an inside-diameter turning tool to the magazine pocket holding the adapter for the long boring bar has been attempted.
Action
Review the pocket number or the type of tool to be assigned.

488 MEMORY PROTECT (MAGAZINE SETUP)

Cause
Tool data updating operations (such as editing tool data, completing the layout of tools, or downloading data on the DATA I/O display) have been attempted during magazine setup.
Action
Perform tool data updating operations after completing the magazine setup operations.
Release the reverse display mode of the [MAGAZINE SETUP] menu item relating to visual tool data management.

489 CANNOT SET THREAD POSITION

Cause
An attempt was made to store the current position for re-threading (using the [THR. POS. TEACH] menu function) without the turning spindle having been rotated through at least one full turn.
Action
Rotate the turning spindle at least through one full turn beforehand to use the above menu function.

490 REGISTRATION NUMBER EXCEEDED

Cause
The data registration has exceeded its maximum value available.
An attempt was made on the TOOL FILE display to register the ninth data item of workpiece material.
Action
Delete unnecessary items to register the desired one.

491 ITEM NOT SETUP

Cause
Data registration is not yet complete.
Action
Check if all the data items are set as required.

492 CANNOT EDIT 3D DATA

Cause
Editing the CAD tool model has been attempted.
Action
The CAD tool model cannot be edited.

493 SELECT JAW TYPE

Cause
An attempt was made to set jaw dimensions without having selected the jaw type (OUT1/IN/OUT2).
Action
Select the jaw type beforehand.

494 NO TOOL SELECT (NOT MGZN TYPE)

Cause
An attempt was made to use the MDI tool selection function on the machine with a turret-type tool-post.
Action
——

495 INCORRECT CAD MODEL DATA

Cause
Registered tool model data contains imperfections (a tool model cannot be drawn with the entered data).
Action
Correct the data in the corresponding section.
Note:
During Parametric model entry…………………..The alarm-causing section is displayed.
During rotating/extruding tool model entry……Causes are displayed.
11:The entered shape has overlapping elements.
12:The entered shape is clockwise (CW).
13:The line connecting the starting and ending points overlaps some other element.

497 HEAD ANGLE INCORRECT

Cause
1. An attempt has been made to storage the tool tip position with the head not in its horizontal machining position (TOOL DATA or TOOL OFFSET display only).
2. An attempt has been made to perform MDI-MMS operation with the head not in its horizontal or vertical machining position.
Action
1. Tool tip position storage (tool length measurement) is possible only with the head in its horizontal machining position.
2. MDI-MMS is possible only with the head in its horizontal or vertical machining position.

498 NO HEAD DATA

Cause
Offset data for the selected head is not registered on the HEAD OFFSET display.
Action
Check if the selected head data is registered on the HEAD OFFSET display.

499 ILLEGAL HEAD TYPE

Cause
An attempt has been made to perform tool tip position storage on the TOOL DATA or TOOL OFFSET display during use of the horizontal type of head.
Action
To perform tool tip position storage for tool length measurement, mount a vertical head or a cover.

1400 SYSTEM ERROR

Cause
An internal trouble has occurred in the system.
Action
Contact Mazak Technical Center or Technology Center with the information of the particular operation causing the alarm, and of the codes displayed in parentheses.

1401 FILE OPEN ERROR

Cause
Trouble has occurred in opening a file from the hard disk.
Action
The file in question might be currently being accessed by another application. Wait for a while to repeat the same operation. If the alarm is not cleared, contact Mazak Technical Center or Technology Center with the information of the particular operation causing the alarm, and of the codes displayed in parentheses.

1402 FILE READ ERROR

Cause
Trouble has occurred in reading a file on the hard disk.
Action
The file in question might be currently being accessed by another application. Wait for a while to repeat the same operation. If the alarm is not cleared, contact Mazak Technical Center or Technology Center with the information of the particular operation causing the alarm, and of the codes displayed in parentheses.

1403 FILE WRITE ERROR

Cause
Trouble has occurred in writing a file on the hard disk.
Action
The file in question might be currently being accessed by another application. Wait for a while to repeat the same operation. If the alarm is not cleared, contact Mazak Technical Center or Technology Center with the information of the particular operation causing the alarm, and of the codes displayed in parentheses.

1404 MEMORY PROTECT (DATA IN USE)

Cause
It was attempted to edit jaw shape data of the machining program currently selected.
Action
Change the selection of the program to edit the required data.

1405 FILE SIZE ERROR

Cause
The size of the loaded file is not correct.
Action
The file in question might be destroyed.
Contact Mazak Technical Center or Technology Center with the information of the particular operation causing the alarm, and of the codes displayed in parentheses.

1406 LOW MEMORY

Cause
Memory size currently available is too small.
Action
Exit all the unnecessary applications to make the best of the NC ones.
If the alarm is caused again, contact Mazak Technical Center or Technology Center with the information of the particular operation causing the alarm, and of the codes displayed in parentheses.

1407 FILE CREATION ERROR

Cause
Creating a file and folder on the hard disk was not successful.
Action
Contact Mazak Technical Center or Technology Center with the information of the particular operation causing the alarm, and of the codes displayed in parentheses.

1408 DATA TRANSFER ERROR

Cause
Data transfer to the NC was not successful.
Action
Contact Mazak Technical Center or Technology Center with the information of the particular operation causing the alarm, and of the codes displayed in parentheses.

1409 MILLING ONLY SELECTED

Cause
The designated function is not available for a program of initial-point scheme (ONLY MILL).
Action
Use the function for a program of another scheme.

1410 MILL &TURN (WPC) SELECTED

Cause
The designated function is not available for a program of workpiece scheme (MILL &TURN) with WPC setting.
Action
Use the function for a program of another scheme.

1411 MILL &TRN (Z-OFS) SELECTED

Cause
The designated function is not available for a program of workpiece scheme (MILL &TURN) with Z-offset setting.
Action
Use the function for a program of another scheme.

1412 INCORRECT G-CODE

Cause
The designated function is not available for the G-code system selected by the F30 parameter.
Action
Correct the program, or change the F30 setting.

1413 INCORRECT RUNNING MODE

Cause
The designated function is not available for the current mode of operation.
Action
Change the operation mode.

1414 PROGRAM WRITING

Cause
Storing a program on the hard disk was not successful.
Action
The file in question might be currently being accessed by another application. Wait for a while to repeat the same operation. If the alarm is not cleared, contact Mazak Technical Center or Technology Center with the information of the particular operation causing the alarm, and of the codes displayed in parentheses.

1415 ZERO CALCULATED TOOL LENGTH

Cause
The LENGTH A item of the tool is set to zero (0).
Action
Check the settings of tool length or tool set data and, if required, measure the tool in question again.

1416 CANNOT INDEX TOOL

Cause
The tool currently indexed on the turret is not appropriate.
Action
Index an appropriate tool beforehand.

1417 PARAMETER ERROR

Cause
The setting in a parameter is not correct.
Action
Check and correct the parameter setting with reference to the codes displayed in parentheses.

1418 CANNOT USE LOWER TURRET

Cause
The current selection of the headstock to which the lower turret is subordinate is not correct.
Action
Change over the headstock selection concerned.

1420 FILE SIZE LIMIT EXCEEDED

Cause
The size of the file is too large for new data to be written in it.
Action
Delete the file, or rename the file.

1422 PROGRAM LAYOUT ERROR

Cause
Creating the data for turret-by-turret display of program layout was not successful.
Action
Change the display mode.

1423 TOOL PATH CHECK NOT COMPLETE

Cause
Since the program has not yet undergone tool path check, the VISUAL TOOL MANAGEMENT display cannot perform calculations for indicating the spare tools to be additionally provided for the machining operation with the program.
Action
Execute the function for tool path check on the program.

1424 BARRIER INFORMATION NOT SET

Cause
In the program-listing mode the [BARRIER INFORM.] menu function is selected without any barrier data being registered.
Action
Select the program-creating mode before pressing the [BARRIER INFORM.] menu key.

1425 ILLEGAL SETUP DATA

Cause
The setup data are not correct.
Action
Make a copy of the program in question on the PROGRAM FILE display, and prepare the setup data for the program copied.

1426 NO PROG LAYOUT FOR THIS PROCESS

Cause
The current process has no program layout information provided.
Action
Press the menu selector key to select a process with program layout data, or select the display mode for all processes.
Alternatively, select a process with program layout data on the PROGRAM (MAZATROL) display or PROCESS CONTROL display and then call up the PROGRAM LAYOUT display from there.

1427 3D INTERFRNCE CHECK MODEL ERROR

Cause
3D remodeling of the workpiece, fixture, or tool has failed.
Action
Modify the entered data.
Confirm the model.

1428 NOT POCKET FOR LONG BORING BAR

Cause
Assigning the long boring bar to a section not defined as a special pocket for the long boring bar has been attempted during the “Layout Completion” operations on the VISUAL TOOL MANAGEMENT display.
Action
Assign the long boring bar to the special pocket.

1429 INCORRECT SELECT TOOL

Cause
Tool setup auto-setting for a tool not capable of using the tool setup auto-setting function (e.g., a magazine tool or a tool facing the No. 1 turning spindle) has been attempted on the TOOL DATA display.
Action
Apply the tool setup auto-setting function only to a turret tool facing the No. 2 turning spindle.

1430 NOT ACTIVE PROGRAM

Cause
This alarm indicates that the machine-operating program and the program selected on the PROGRAM (MAZATROL) display differ during execution of the workpiece transfer storage function on the PROGRAM (MAZATROL) display.
Action
Match the machine-operating program and the program selected on the PROGRAM (MAZATROL) display.

1431 AUTO SET ERROR

Cause
Tool data
Action

1432 NO SELECT TOOL MODEL

Cause
The tool model to be copied/erased/renamed is not selected.
Action
Select the appropriate tool model before performing the copy/erasure/name change.

1433 SAME TOOL MODEL EXISTS

Cause
A registered tool model has been specified during the copy/name change.
Action
Specify an unregistered name.